Pages

Wednesday, April 16, 2014

How to Insert an Invisible Zipper: A Tutorial

Here are a few tips to help you tackle invisible zippers! 


There seems to be an infinite variety of zippers out there – the exposed zipper is getting a lot of attention these days on the fashion front, but I generally prefer that the closure on a garment does not scream so loud.  An invisible zipper is an inconspicuous option – it hides in the seam of the fabric so that all that remains visible is the elegant pull tab.


If you need to shorten your zipper, now is the time.  [Something to keep in mind is that because the invisible zipper turns inward, it is difficult to stitch in that fold the closer you get to the zipping mechanism.  If I have an extra inch to work with and I am not fighting against the metal pull, I like to use it.]    


To make it easier to access the zipper stitching line and keep the folded invisible coils out of the way, you can iron the zipper open using a low/synthetic setting on your iron with no steam.  I usually take a quick pass at my invisible zippers with an iron, but do not attempt to flatten them since it can affect the integrity of the zipper.  Also, too much heat can melt the teeth together, ruining the zipper (please don't ask me how I know that!).


The trick I find most helpful for installing (any) zipper is to reinforce the opening edges of the garment.  Invisible zippers, especially, have a tendency to pooch out at odd angles in lighter weight fabrics that have not been stabilized.  

A strip of silk organza is an excellent option, as is a strip of fusible interfacing (make sure to choose an appropriate weight for your garment fabric).  The strip needs to be wide enough to extend beyond either side of the seam fold so that the stitching line will catch your chosen stabilizer.  For an invisible zipper, one inch is plenty.  Also make sure that the interfacing is longer than the zipper opening.  The point where the fabric seam meets the zipper opening is likely to get a lot of stress and the interfacing will help to reinforce that spot.


Mark just inside the seamline (depending on your fabric, a fabric pen, chalk, or even a pencil will do the trick).  For an invisible zipper, this line will need to be visible on the right side of the fabric.  


This particular fabric is not easily marked, so I drew my mark on the wrong side and basted that line with thread.  This makes the line visible on the right side of a highly textured fabric.


If there are horizontal seams that cross your zipper opening,  trim your fabric layers, and baste those horizontal seams in place.


I find the easiest way to figure out which way to insert the zipper itself is, with the right side facing and the zipper next to the opening seam, right side up.  When I begin to fold the seam allowance away from me (to the wrong side where it belongs) the zipper should disappear, leaving the pull tab visible.  In other words, the tape edge should be close to the raw edge of the fabric, and the zipper coil should be just hanging over the marked seamline.


The second most important part of zipper installation is basting, which saves a massive amount of time in the long run – so don’t skip this step!  I like to use a contrasting silk thread so it is easy to remove later on.


Once one side of the zipper is basted in place, it is time to stitch it down.  Many machines come with an invisible zipper foot.  If you do not have one, a regular zipper foot can do the trick, depending on how mobile your needle is.  The stitching line needs to get as close as possible to the plastic teeth without grabbing them.  I do not recommend the plastic invisible zipper kits that only cost a few dollars – the plastic slide can move around while you sew which is extremely frustrating.


Another option is hand stitching.  I know the first time I heard of someone hand stitching a zipper I thought they were crazy.  But a tiny backstitch/pick-stitch/prick-stitch is incredible sturdy and works beautifully.  It also gives you the most control.


One thing that will help to ensure a beautiful application is to stitch both sides of the zipper in the same direction.  If you start from the top and work your way down on the right hand side, work from the top down on the left side as well.  This will help to keep your fabric from shifting in opposite directions.  If you have trouble matching seamlines, this may solve your problem!


Speaking of seamlines . . . if you have any horizontal seamlines to match, you will want to mark those after one side of the zipper is stitched into place.  Close the zipper, and mark the seamline point on the zipper tape with a fabric pen or chalk (I prefer a fine point pen – the thinner the mark, the more accurate the placement).


Matching any seamlines necessary, baste the second tape into place.  


Now make sure to zip everything closed to check that those seamlines are matching up!  If not, remove the basting and try again.  


Once you are happy with the zipper placement, stitch it into place, remembering to stitch this seam in the same direction as the last.


Next you will need a standard zipper foot to close up the seam below/above the zipper.  Remove the basting stitches, and push the end of the zipper out of the way.  


Pin the seam closed below your newly installed invisible zipper.  The end of this seam should overlap the zipper stitching slightly.


As a final note, I will say that I prefer to install invisible zippers in an open seam.  I find it much easier than fighting with the twisting coil against a closed seam.  If possible, I will insert a zipper before adding other pattern pieces to the mix.  This is not always possible, but the less fabric you have to flip around, the easier it will be!

Things do not always go according to plan, as evidenced by this project.  As much as I love the look of an invisible zipper, they are far from sturdy.  I had a feeling that this fabric was too bulky for an invisible zipper, but my stubborn streak thought I could make it work – the dress had different ideas.  Instead of fighting to get it open and closed every time I wear the dress, I decided a lapped zipper would be a much safer bet.


The problem was that the loose weave of the fabric was coming apart and a lapped zipper needs plenty of seam allowance to work properly.  So out came the silk organza.  I ripped a two inch strip and applied it to the raw edges.  When turn under, it covered the raw edges


Crisis averted!


Invisible zippers are brilliant tools, when used with a suitable project; when installed properly, they are virtually undetectable.  But they are best used with light to mid weight fabrics.  


Close fitting garments may require an extra pair of hands to zip them up or the help of a hooked waist-stay.  I have a number of vintage invisible zippers with metal teeth which are a bit stronger, but they still have to twist inward in order to close which is not nearly as stable as a standard zipper. 


And should your invisible zipper application go completely awry, step away from the project for a chunk of time and then have at it with a seam ripper.  The invisible zipper is a fickle mistress – worth the effort in certain circumstances, but she definitely has a mind of her own!

Do you have any invisible zipper stories of your own?


[The fabric for this project was received in exchange for my contributions as a Britex Guest Blogger.]


10 comments:

  1. Thank you for this incredibly helpful tutorial with all of those pictures! It looks like this method gives you a lot of control, and I had no idea you could do a hand-picked version of an invisible zipper.

    ReplyDelete
  2. Another wonderful tutorial!
    Zippers of any kind are my nemesis and invisible ones always seem to catch warp and break for me.
    I will follow this next time, hopefully with better results!!

    ReplyDelete
  3. I totally felt the same way about hand-sewing zippers. Then I tried it when I only had an invisible zipper to go in a tricky side seam and it ended up being the best-looking zipper I've ever put in. I may do them all by hand from now on.

    ReplyDelete
  4. You really do the most wonderful tutorials...I always put them on my 'to try' list! Thanks!

    ReplyDelete
  5. I haven't made that many zipped garments so far...but everytime I try to insert an invisible zipper it ends up as an epic fail! Most of the time I avoid them and prefer by far hand picked zippers, which, as you say, are the solution that offers most control!

    ReplyDelete
  6. Great tutorial! I usually stay away from invisible zippers, but after using one recently for the first time in a while and having it work out nicely, I'm a little more inclined to start using them again. I didn't know you could sew one in by hand, though. I'll try this for my next one!

    ReplyDelete
  7. I find it hard to put an invisible zipper in a bias seam. not that it stops me from doing so but sometimes I have to do it more then once to get it in correctly.
    my scariest event with an invisible zipper though occurred last year, when I had taken up the bodice of a prom dress. I had to reset the zipper and with all the beading and sequins it was so thick it refused to zip up on the girl. it went up and down just fine off of her. and of course I didn’t know there was a problem till the day of the prom. I fixed it though and she was only a few minutes late for her pictures. disaster averted but talk about being a bit stressed.

    ReplyDelete
    Replies
    1. Aaahh . . . zipper nightmares! She is lucky she did not have to be sewn into the dress - it sounds like you work very well under pressure!

      Delete
  8. Great tutorial and I've read a few over the last few weeks after making my first dress. I think I will go for hand picked in future as surely more satisfying and probably quicker for me. I am so devastated though as I zipped it up the other day the zipper pull itself came right off the top- I had to trim the top down as I had melted the teeth. How on earth do I get that zipper pull back on. The idea of trying again is awful. For now I'm taking your advice and stepping away. Any help out there?

    ReplyDelete
  9. I feel your frustration. Depending on the kind of zipper, you may not be able to get the pull back on track (and it certainly will not be possible once frustration sets in!).

    I think the only way to ensure that the same thing will not happen again would be to start with a fresh zipper, complete with upper stoppers. That is probably not what you want to hear, but having had to remove two zippers in the last couple of months, it really is not as bad/time consuming as I expected.

    Good luck!!

    ReplyDelete